... trimmer, use for polishing and cutting the gypsum plate. drywall board. 1.Gypsum plate edge trimmer2.Suitable for the trimming of cutting ... ,3.especially for the edging and chamfering of gypsum plate(cement fiber pressure plate)4.and helpful to realize flat and smooth seaming ... :60 MEAS:52×36×60 GW/NW(KGS):15/16Gypsum plate edge trimmer(trimmer,decorating tool)
... good use. Innovative products 860 Caigang pressure tile machine quality best, contact email: The pressure plate and the pressure tile machine roll forming, both ... series. The roof tile pressure equipment, high-speed guardrail plate molding equipment, large car plates pressure equipment, clamping groove plate pressing equipment, rolling shutter ...
... One set of oil pressure system to control the hydraulic system driving the pressure plate hanging round the upper and ... lower. Configuration lifting gear box 12 pcs; Cardboard machinery equipped with hydraulic systems. * Pressure ... 800mm;Lower driving rollers: Ø800mm;*Heating section is tense pressure roller structure, cardboard sticks firmly and levels off.* ...
1800T Sawing machine used to saw and cut Aluminum profile . Technical parameters of Sawblade1. Diameter of saw blade: 650 inch2. Cross travel: 850mm3. The thickest of cutting size: 230 mm4. Direction: right or left5. Pneumatic pressure plate: Yes6.Countertop materials: slab rubber7.Sizing frame: No8.Sent material cradle: No9.Cooling mode: oil fog 1800T Sawing machine
... This machine is mainly used for testing the anti-pressure strength of concrete building materials, like concrete, cement and ... : ±1%;4. Upper pressure plate size:φ220mm;5. Lower pressure plate size: φ300mm6. Distance between upper plate and lower plate: 320mm;7. Maximum piston ... the accuracy of test load readout, it adopts oil pressure transducer to measure the load, after amplifying, the test ...
... strips are fixed on the other side. As the steel plate can be heated and cooled at the same time, the ... moving can be assured. The longitudinal guide ways firmed by pressure plate backing board and connecting sleeve, all made by high intensity ...
... compression, double cylinder controlled by pressure plate. When material fed into the cutter, the pressure plate will press the cylinder, when ... the material process to the end of cutter, the pressure plate will release the cylinder. Specification of space rings: 3 ... and unloading of materials. Movable range of guide stock plate: 350mm.Technical ParametersMin. cutting width: 3mm Effective cutting ...
... printing position, iron, as far as possible when ironing back pressure, time, maintain 8 seconds before the end of the two ... is recommended to use, the temperature setting plate backing machine for 200 degrees Celsius, pressure plate backing machine wait 10 seconds left lift ...
... One set of oil pressure system to control the hydraulic system driving the pressure plate hanging round the upper and ... lower. Configuration lifting gear box 12 pcs; Cardboard machinery equipped with hydraulic systems. * Pressure ... 800mm;Lower driving rollers: Ø800mm;*Heating section is tense pressure roller structure, cardboard sticks firmly and levels off.* ...
... .3. Hydraulic control system: one set of low-noise high-pressure gear pump (Marzocchi) and specialized three-phase asynchronous motor.4 ... ); (0-30, φ13-φ40mm)B. One set of compressing clamp; (pressure plate φ160mm)C. One set of bending clamp; (cold bending plunger ...
... in-line with water cooling, turbo-charging and intercooling.Clutch: Single-plate coil-spring clutch, diameter 420mm, hydraulically operating with air assistance. Service ...
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2022 ECOL Limited and/or its subsidiaries and licensors. All rights reserved.