Ads by Google
1,Preface
Dear users,
To ensure better performance of your e-bike, please read through the J-LCD product introduction carefully before using it. We will use the most concise words to inform you of all the details (including hardware installation, setting and normal use of the display)when using our display. Meanwhile, the introduction will also help you solve possible confusion and malfunctions.
2,Material and Color
J—LCD products are made of black PC material. Under the temperature of -20°C to 60°C, the shell material can ensure normal usage and good mechanical performance of the products.
3,Function Summary and Button Definition
J—LCD user settings include local time setting, top riding speed setting, metric system/English system setting(MPH and Km/H,Mile and Km),wheel size setting(18—28inch),LCD backlight brightness setting.
J—LCD displays battery capacity, time, motor power ratio, riding speed, riding distance, 6Km/h power assist walk, and malfunction code of the electronic control system.
J—LCD is equipped with special 30 button. The button can be installed either on the left side or on the right side of the handlebar. Its shape is as follows:
Error Code Display
7, Button Battery Replacement
Ride your bike in a safe way. Don’t hit or knock the display. When you replace the display battery, please detach the display from the handlebar first. Take off the battery cap and put in a new battery.
The model of the display battery is CR2032. This button battery is used exclusively for the timer IC inside the display. The life of the button battery is more than 3 year.
Attention: After replacement the button battery, please set the time of the display.
8, FAQ Answers
Q:Why can’t turn on the display?
A:Please check if the cable is well connected with the controller.
Q:Why the timer error?
A:Please replace the button battery. The battery model is CR2032.
Q:How to deal with the error code display?
A:Contact the e-bike maintenance station in time.
9, Quality Warranty
OutRider® is not responsible for the scratched or broken shell after the products are delivered out of the factory.
We don’t repair scratched or broken lead wires.
The LCD display function warranty: 18 months starting from the first usage of the user.
The button battery warranty: 36 months from the delivery time of the display out of the factory.
10,Circuit Block Diagram
Red: 24V/36V, Blue: lock wire, Black: GND, Green/Yellow: RX/TX wire.
If using the water proof connector, Users cannot see the leads color of the internal wiring.
11,Software Version
This operating instruction is a general-purpose software (version V2.0). Some of the version of the e-bike LCD may have slightly different, all with actual use version.
30 button is connected to the bottom of the display through wire cable.
4,Installation Instruction
Fix the display and 30 button onto the handlebar and adjust to an appropriate visual angle. Match display connectors with controller connectors.
5,Setting
Make sure that the connectors are matched well. Turn on the e-bike power supply.
Start and Entry Setting
Press the MODE button and start the display.
After start-up, please hold both UP and DOWN at the same time, for3 seconds, LCD will enter into the setting state.
Time Setting
After entering into the setting state, first set the HOUR by using UP and DOWN. Press MODE for confirmation and then set the MINUTE by using UP and DOWN. Press MODE for confirmation and then set the top riding speed.
Top-speed Setting
The default figure of the top riding speed in the display is 25 Km/h.
You can change this figure and re-set a new top riding speed. If the e-bike speed exceeds this new figure, the controller will cut off motor’s electricity so to ensure the rider’s safety.
The setting range of top riding speed is from 10Km/h to 35Km/h.
After setting the top riding speed, please press MODE for confirmation and enter into the display unit setting.
Choice of Display Unit (Metric system/ English system)
Press UP or DOWN choose a display unit.
The unit could be MPH and Km/H. The range unit is changing accordingly with the speed unit.
Wheel Diameter Setting
Press MODE for confirmation and then enter into wheel size setting.
Press UP or DOWN and choose a corresponding wheel diameter to ensure the accurate display of speed and distance. The interface is as follows:
Press MODE to confirm the wheel size and enter into the LCD backlight brightness setting. The default value of the wheel size is 26inch.
Backlight Brightness Setting
Press UP or DOWN to modify the backlight brightness. You can choose from level 1 to level 3. Level 1 is the minimum brightness. Level 3 is the maximum brightness.
The default value of the backlight brightness in J—LCD display is level 1.
Exit Setting
In the state of parameter setting, short press MODE(within 2 seconds) to make confirmation. Hold MODE (more than 2 seconds), save the current settings and exit the setting interface.
6,Normal Operation
On/Off
Press MODE and the display starts to work for the controller power supply.
In the Power On state, hold MODE to cut off the e-bike power supply. In the Power Off state, the display and the controller don’t use the battery power supply. So the power consumption is ZERO.
Suggestion:If you won’t use the e-bike in 4 hours, please take the battery off the e-bike and put it away in a proper place.
Speed Display (Current Speed/Average Speed/Max Speed)
When the e-bike starts, the display will automatically show the current speed.
Hold UP and the display will show the MAX speed during this ride. Hold UP again and the display will show the AVG speed during this ride. Hold UP again and the display will turn to the current speed display.
Assisted Power Select or Throttle Level Select
Press UP or DOWN change the output power of the motor. The power ranges from Level 1 to Level 5. Level
1 is the minimum power. Level 5 is the maximum power.
The default level is Level 1.
Power Assist Walk
Hold DOWN and enter into the mode of power assist walk. The e-bike will go on at a uniform speed of 6 KM/H.
Warning:6Km/h “assisted power walk” function can only be used when the user is pushing the e-bike. Please don’t use this function during riding.
Turn On and Turn Off the Backlight
Hold both UP and MODE for 3 seconds and turn on the J—LCD backlight. When the surrounding light is not enough or it is in the evening, you can turn on the backlight. Hold both UP and MODE for 3 seconds again and you can turn off the J—LCD backlight.
6.6 Distance Display (Riding Distance/Total Distance)
Press MODE and change between riding distance and total distance. This function is convenient for users to check the riding distance (TRIP) and the total distance (ODO).
Capacity Display
When the battery capacity is high, the five battery segments are all light. When the battery is low voltage, the battery display frame will flash at the frequency of 1 HZ. This indicates that the battery is severely low voltage and needs to be recharged immediately.
Malfunction Code Display
If there is something wrong with the electronic control system, the display will show the error code automatically. The following are some definition of malfunction codes.
Definition Diagram of Error Codes
BP LCD display