Ads by Google
DTA compress garbage truck / compress garbage truck/ garbage compactor truck/refuse compression truck manufacturerOur factory production compress garbage truck your best choice . 24 hours phoon:TEL:0086-15271357675
the compression garbage truck are mainly used for carrying the elevation waste bin, also can used for the conneyance ash,sand ,detritus,soil,etc
compression garbage truck 1.hermetic design 2.aviod re-polluting 3.general iron or plastic barrel is OK 4.hydraulic compress
Product | DTA5208 /5250ZYScompression garbage truck | |
Chassis type | EQ1208GJ5EQ3208GJ /EQ3254GJ /EQ1254VJ | |
CubageT | 16-18 | |
Parameters | Overall dimension length/width/height (mm) | 8120×2495×3260 |
Total Mass(kg) | 21900 / 24995 | |
Payload(kg) | 10000 | |
Kerb Mass(kg) | 11705 | |
Approach angle/ Departure angle(mm) | 32/20 | |
Front suspension/rear suspension(mm) | 1245/2075 | |
Fuel Type | diesel | |
Fuel Consumption/100 km |
| |
Max Speed | 80 | |
Engine | Type | EQB210-20 C260 20 |
Displacement/Power(kw) | 5880/155 | |
Manufacturer | Dongfeng Commins Diesel Engine Co., Ltd | |
Type |
| |
Chassis | Drive type |
|
Wheelbase(mm) | 3500+1300 | |
Tread(front/rear) | 1940/1860 | |
Front axle |
| |
Rear axle |
| |
Steering gear |
| |
Transmission |
| |
Clutch |
| |
Braking system |
| |
Cab |
| |
Number of spring axle(front/rear) | 8/13 | |
Tire Type | 10.00-20 | |
Air-condition | Choose to fix | |
Special specifications
container volume | 3~16 m³ |
The weight of Manipulator rolling-over(kg) | equal or greater than 600kg |
The volume of filler (m3) | 1.9 |
Rated pressure of the hydraulic system | 19Mpa |
Filler mouth lowest part and ground distance | 1080mm |
The filler operating time | Equal or less than 30s |
Pusher plate dumping of garbage time | 50s |
The lifting time of the filler | equal or less than 15s |
The volume of drain tank | equal or greater than 300(L) |
The QTY of hanging barrel on the manipulator | 3(240L square barrel)/2(300L square barrel )/1(660L square barrel) |
We welcome you come to visit our factory
It has three convenient and reliable operation ways: automatic operation, manual operation with electricity, manual operation. Comparing with the same internal and external industry, we have been in leading position in technology.
Control panel is set in cab, making person not need to get off to operate. Sewage is collected by sewage sinks in front part as well as rear part of vehicle. Cover of sewage sink is easy to open and well-sealed. Horseshoe sealing strip is used in joint of filler and container, providing pre-pressed technology to avoid out leaking of sewage.
The movement of scraper and slider can be operated by button penal which is in side board of rear part of filler automatically or manually with electricity. Automatic operation can realize four working procedures which are scraper extending, slider going down, scraper retracting, slider going up to load and compress garbage continuously. Manual operation with electricity controls four working procedures to operate respectively. Buttons in cab can control filler lifting and descending, pusher extending and retracting, guarantying operator loads and dumps garbage in cab. Handle of hydraulic valve block in front part of container can pull and push manually to operate each working procedure. So choose one operation way in your convenience shows the concept of human-oriented fully in our design.
with high workmanship, reasonable price.
DTA5208 /5250ZYS compression garbage truck / garbage compactor truck/refuse compression truck manufacturer