Liquid oxygen 175L Dewar

Cryogenic welded insulated cylinder:

liquid gas cylinder

Standard features list
standard		160		180		200
pressure		MP	HP	MP	HP	MP	HP	VHP
Capability(L)	Geometric volume	175		196		210		204
Size and (safety valve) open pressure settings
Safety valve setting	psig/ MPa	230/1.6	350/2.4	230/1.6	350/2.4	230/1.6	350/2.4	500/3.45
diameter	CM	50.8
height	CM	151.3		161.3		167.1
Empty weight(KG)		113.4	126.9	117.9	136.1	126.9	145.1	170
Full weight(KG)	N2*	234	241	253	263	271	280	286
	O2*	285	290	309	318	331	339	349
	Ar*	322	325	351	357	375	380	386
	CO2*		303		331		353	354
	N2O*		293		321		343	344
Gas volume under standard state(NM3)	N2*	97	91	108	102	115	108	93
	O2*	120	114	134	127	143	133	123
	Ar*	117	111	130	124	139	130	120
	CO2*	-	89	-	99	-	105	93
	N2O*	-	84	-	94	-	100	88
functions
Daily evaporation rate(% per day)	N2	2		1.9		1.85		2.0
	O2- Ar	1.4		1.3		1.2		1.4
	CO2 - N2O	-	0.5	-	0.5	-	0.5	0.5
Air current(NM3/Hr)	N2,O2,Ar	9.2		9.2		10.5		9.2
	CO2,N2O	-	2.9	-	2.9	-	2.9	2.9
Under the settings of safety valve(open pressure)

Booster coil1Gas valveexport gas2Fill/export liquid valvefill or export the liquid3Pressure control valvecontrol (turn on/off) the pressure control adjuster.4Vent valverelease the pressure5Combined pressure control adjusterautomatic control the pressure6-8Pressure gauge, safety valve, bursting disc9Liquid level detectorliquid capability of wielding insulation cylinder

New type workshop centralized gas feeder: dewar flask centralized gas feeding system sketch map:

New type workshop centralized gas feeder: dewar flask centralized gas feeding system sketch map: Features:1It is operated easily, used conveniently and accounted easily. Its highest working pressure is 1.6MPa.2The air flow is large and stable.Brief introduction about dewar flask:Firstly, outer structure of dewar flask: Dewar flask has four valves they are liquid valve, air valve, vent valve and pressurization valve as well as gas pressure gauge and level gauge.Secondly, usage: Your company is using the dewar flask. The firs step is to connect the pipe where the dewar flask liquid vavle lies with evaporator by the high pressure metallic tube. After the confirmation of connecting, you can turn on the liquid valve. If the gas pressure to the workshop can not meet the demand, please turn on the pressurization valve. A few minutes later, the pressure will rise to the using demand. Then you can make use of it. If the dewar flask has no liquid phase and the pressure of gas phase is only 5kg, it means that the gas in dewar flask has used up. Please turn off the using valve and stop using.Thirdly, some questions you should pay attention when using the storage1When the dewar flask storage has not been used, do not turn of the pressurization valve. You must check whether the pressurization valve is turned off tightly. Otherwise, the gas leak in the vessel.2You must turn off the pressurization valve when stop using. The pressurization valve is open only when it is used.3When thepressurization valve is turned open totally, the dewar flasks pressure gauge is no longer raise, than means there is no liquid phase only gas phase left in the vessel.

Liquid oxygen 175L Dewar